About the power bank circuit In this project, we will be making a power bank using a pre-built power bank circuit and 18650 Li-ion cells. This power bank…
Are you a beginner in Electronics wondering where to start? Well, we’ve all been there once like you, swimming on the shores not knowing where to go and…
UJT Characteristics The static emitter characteristic (a curve showing the relation between emitter voltage VE and emitter current IE) of a UJT at a given inter base voltage…
In this article, we learn about UJT (Uni Junction Transistor) in detail. We cover a lot about UJT like – what is basically a UJT, how they differ…
Light activated SCR (LASCR) or a Photo SCR is just an ordinary SCR except that it can also be light triggered. Most LASCRs also have a gate terminal…
Gate turn-off switch (GTO) is, like an SCR, is a four layer, three junction semiconductor device with three external terminals, namely, the anode, the cathode and the gate,…
The diac and the silicon bilateral switch are grouped as bilateral or bidirectional devices because they can breakover in either direction. There are also breakover devices which breakover…
Silicon bilateral switch (SBS) is another breakover device which is capable of triggering triacs, and it is popular in low-voltage trigger control circuits. They have breakover voltages lower…
The four-layer diode, also called the Shockley diode after its inventor William Shockley, is essentially a low-current SCR without a gate. It is classified as a diode because…
Silicon controlled switch (SCS), like the SCR, is a unilateral, four layer three junction P-N-P-N silicon device with four electrodes namely cathode C, cathode gate Gx, anode gate…
As mentioned earlier, low-current drop out is the normal way in which the SCR is turned off. Gate-controlled switch is designed for easy opening with a reverse-biased trigger.…
Introduction to IGBT-Insulated Gate Bipolar Transistors Insulated gate bipolar transistor (IGBT) is a new high conductance MOS gate-controlled power switch. The fabrication process is similar to that of…
Power MOSFETs are usually constructed in V-configuration, as shown in figure. That is why, the device is sometimes called the V-MOSFET or V-FET. V-shaped cut penetrates from the…
Cross-view of a dual-gate N-channel depletion type MOSFET is shown in figure. It acts as if two FETs are connected in series, as is obvious from figure. The…
Although DE-MOSFET is useful in special applications, it does not enjoy widespread use. However, it played an important role in history because it was part of the evolution…
We know that when the gate is biased negative with respect to the source in an N-channel JFET, the depletion region widths are increased. Theincrease in the depletion…
Introduction to MOSFET-Metal Oxide Semiconductor Field Effect Transistor, Metal-oxide-semiconductor field-effect transistor (MOSFET) is an important semiconductor device and is widely employed in many circuit applications. Since it is…
Unlike BJTs, thermal runaway does not occur with FETs, as already discussed in our blog. However, the wide differences in maximum and minimum transfer characteristics make ID levels…
From the circuit named “looking into the drain” of the FET it is seen (for small signal operation) an equivalent circuit consisting of two generators in series, one…
What is a Junction Field Effect Transistor? A JFET is a semiconductor with 3 terminals, available either in N-channel or P-channel types. It is unipolar but has similar…
As already mentioned in Field Effect Transistors (FET) , JFET’s are of two types, namely N-channel JFETs and P-channel JFETs. Generally N-channel JFETs are more preferred than P-channel.…
Introduction to FET-Field Effect Transistor So far we have discussed the circuit applications of ordinary transistors, in which both holes and electrons take part. This is the reason…
This blog post is continuation to the original post: Fabrication techniques of a P-N junction diode 1. Grown Junction Diode: Diodes of this type are formed during the…
General Introduction to Fabrication techniques of a P-N junction diode: In practice, the P-N junction is formed from a single mono crystalline structure by adding carefully controlled amounts of…
The photoconductive cell is a two terminal semiconductor device whose terminal resistance will vary (linearly) with the intensity of the incident light. For obvious reasons, it is frequently…
